Article ID : 00024610 / Last Modified : 09/06/2016

Connecting, Please Wait appears in the display of the portable player.

Applicable Products and Categories of This Article

IMPORTANT: This article applies only to specific products and/or operating systems. Check the Applicable Products and Categories section of this article before starting these steps.

Follow this procedure to troubleshoot if the portable audio player (device/media) is not recognized by the computer:

IMPORTANT: If model-specific information is required to complete any of the steps in this solution, refer to the operating instructions supplied with the product. Manuals are posted on your model support page.

NOTES:

  • Depending on the model, CONNECT, USB Connect, PC Connect, or PC-<-will appear in the display of the portable player when an appropriate connection has been established.
  • If you are attempting to use your portable player on an additional computer, be sure the device is authorized  (if applicable). Authorizing your device will initialize (format) the data.
  1. If you are using the Microsoft® Windows® 2000 Professional operating system, be sure that you are using the latest service pack. The portable player may not be recognized with some earlier versions.
  2. If you are using the Microsoft® Windows Vista™ operating system and a Net MD™ or Hi-MD™ Walkman® recorder, download and install the compatible device driver update. Downloads are posted on your model support page.
  3. Make sure that the player is in STOP mode (not playing a song).
  4. Be sure that the computer meets the system requirements of the software.
  5. Power the portable player using AC adapter (if applicable).

    NOTE: If your model requires battery power, replace the battery(s) with a new one.

  6. Check that the USB cable is firmly connected to both the computer and the portable player.
  7. Check the connection status again.
  8. If the portable player is connected to a USB hub, disconnect it and connect it directly to the computer with a dedicated USB cable.
  9. Check the connection status again.
  10. If the portable player is still not recognized by the computer, disconnect the USB cable and restart the computer.
  11. After the computer restarts, connect the USB cable and test the connection again.
  12. If the portable player is still not recognized by the computer, try a different USB port.
  13. Check the connection status again.
  14. If possible, connect a different USB cable to determine if the current cable is defective.
  15. If there are other devices connected via USB, temporarily disconnected them.
  16. Check the connection status again.
  17. Check the device manager for conflicts. If there are any conflicts, including conflicts among devices other than the portable player, they should be resolved .
  18. If the portable player is still not recognized by the computer, the driver may not be correctly installed. A procedure is available to check the Device Manager to verify proper installation .
  19. Uninstall and then reinstall the SonicStage software.
  20. If your model has a built-in initialize/format utility, initialize the player.
  21. If your model has a USB connection setting, set it to 100mA / Low-Power 100mA / Low-100mA . Please refer to the Operation Guide for your model for more information about the USB connection setting.
  22. If the issue is still not resolved, it is possible that your Windows installation is corrupt and will need to be reinstalled. Try using the portable player on a different computer. If it works, the issue is with your computer. Contact the manufacturer of your computer for reinstallation procedures.

    NOTES:

    • Before performing any type of reinstallation, always back up important files/information.
    • To use a portable player that included an earlier version of the OpenMG™ Jukebox or SonicStage® software with a VAIO® computer pre installed with a later version of the SonicStage software, install the drivers only. Do not install the earlier version of the OpenMG Jukebox or SonicStage software over the top of the later version of the SonicStage® software. Use the OpenMG Jukebox or SonicStage software CD that came with the portable player to install the drivers.
    • When reinstalling the software or drivers, do not connect the portable player to the computer until after the installation has completed.
    • If the connection or disconnection is not recognized when using the OpenMG Jukebox software, use the OpenMG Jukebox 2.2 installer CD to reinstall the drivers via the Device Manager .
    • If this issue is occurring when using the Net MD Simple Burner software, a Net MD Simple Burner Update Program (UPDATE_SB1003.EXE) to resolve this issue is available on the Digital Music Player Support Web site at http://www.sony.com/walkmansupport.
    • If the issue is still unresolved, service may be required. Begin the procedure to send your Sony product into a Sony facility to be repaired.

NOTE: Information regarding upgrading to the latest version of Sony's music management software is available at the Digital Music Player Support Web site at http://www.sony.com/walkmansupport. Please note system requirements prior to upgrading your current application.