This information is for the following models:

  • ILCE-9M2

About this download

Benefits and Improvements from the latest update

  • Adds the Hi Frequency flicker function, which allows you to reduce the impact of flickering of artificial light sources (e.g. digital signage, electronic signboards, LED lights, etc.), by more finely adjusting the shutter speed
    NOTE: The Hi Frequency flicker function cannot be accessed through the Imaging Edge Remote, Imaging Edge Mobile, or Remote Camera Tool software (as of April 9th, 2020).
  • Improves the Face/Eye Priority in the AF function:
    • When set to a custom key, the Face/Eye Priority in the AF function can be activated or deactivated each time the custom key is pressed
    • If Face/Eye Priority is already set to custom key, this improvement will be available after the camera is updated
  • Improves the Remote Camera Tool function by adding support for displaying Focus Frame for almost all scenes
    NOTE: Version 2.00 (or later) of the Remote Camera Tool is required. Please update to the latest version.
  • Improves the FTP transfer function
  • Allows the camera's MAC address to be displayed as a QR code
  • Adds a function to close the shutter when you turn off the camera to prevent dust or debris from adhering to the image sensor when you change lenses
  • Allows you to save or load the customized camera settings to My MENU
  • Improves the overall stability of the camera

For updated function usage and additional information, please refer to the ILCE-9M2 Help Guide. Additionally, a revision has been made to the instruction manual according to this update. The latest version of the instruction manual can be downloaded from referenced website.

Previous Benefits and Improvements

The following benefits and improvements are also included in this update.

  • FTP transfer can be started earlier after shooting pictures
  • Improves the overall stability and performance of the camera:
    • Corrects a condition where the camera can sometimes turn off when playing RAW images
    • Improves JPEG image quality when shooting under specific conditions

File Info

File Name

  • ILCE-9M2 System Software (Firmware) Update Ver. 2.00 (Mac)

File Version

  • 2.00

File Size

  • 327 MB (327,035,788 bytes)

Release Date

  • 04-09-2020

Before You Start

Check the system software version

Follow the instructions below to check the system software version. If the system software version is Ver. 2.00, the update is not required.

  1. Select "Menu" → "Setup subpage [6]" → "Version" on the camera.
  2. The system software version is displayed as illustrated below.
    System Software Version

System Requirements

Operating Systems

The latest version of the system software update is compatible with the following Macintosh versions:

  • Apple® macOS® 10.13 – 10.15

Computer Hardware

The latest version of the system software update is compatible with the following hardware:

  • Hard drive space: 600 MB or more
  • RAM: 512 MB or more

Other Hardware

  • Power source for the device: Fully charged rechargeable battery pack NP-FZ100.
    NOTE: The update can only be performed when the battery power level is Battery Power Level (three bars) or more. We recommend that you use a fully charged battery. Detach the vertical grip before updating system software.
  • USB cable supplied with the device
    NOTE: Update functionality is not guaranteed with any other USB cable.

Download & Install

Important Notice

  • Please close all other application software before updating the system software.
  • Use a fully charged rechargeable battery pack NP-FZ100.
  • Do not remove the battery during the update as the sudden loss of power may render the camera inoperable.
  • Remove the memory card from the camera before starting the update process.
  • The system software update takes approximately 15 minutes. Please prevent your computer from going into Sleep mode during this time.
    NOTE: If the computer does go into Sleep mode and the update is interrupted, the entire update process will need to be restarted.
  • Do not open "About This System Software Updater" in the System Software Updater menu as this may crash the Updater software.
  • Do not connect the camera to other any other devices except your computer.
  • Do not connect the camera and computer yet.

How to download the Updater:

  1. After reading the disclaimer, click Download.
    NOTE: Before downloading the software, we recommend that you create a Sony account. After creating a Sony account or signing in with your Sony account, download the software (For customers in the USA).
  2. The file [Update_ILCE9M2V200.dmg] file will start downloading.
  3. Save the file to the desktop of your computer (recommended).

Step 1: Start the Updater

  1. Close all currently running programs on your computer.
  2. Double-click the [Update_ILCE9M2V200.dmg] file you downloaded. Do not connect the camera at this point.
    NOTE: If you have connected the camera to a computer, disconnect it before following the procedure.
  3. [Update_ILCE9M2V200] is expanded.
  4. Double-click the [UpdateSetting Tool] icon. UpdateSetting Tool
  5. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.
    Enter the User Name and Password
    NOTE: After the message from the system is displayed, the security and privacy screen will be displayed.
    • If the following message is displayed before "Security and Privacy" is displayed, press the [OK] button.
      Press the OK Button
    • Open the "General" tab on the "Security and Privacy" screen and allow reading of "Sony Corporation" system software.
      Security and Privacy screen
      NOTE: If you approved in the past, the security and privacy screen will not be displayed.
    • If you are asked to restart macOS after pressing the [Allow] button, please restart and return to the beginning of the update procedure.
    • If the [Allow] button is grayed out, click the lock icon to unlock it, and then press the [Allow] button.
    • If the [Allow] button is not displayed, connect to the Internet and try again from the beginning of "Step 1: Start the Updater ".
    • If the "Security and Privacy" screens remain displayed, please close the window.
    • If the message displayed together with the "Security and Privacy" screen remains displayed, close both with the [OK] button.
      System Extension Blocked screen
  6. Connect the camera to the computer.
    • A dialog for USB connection will be displayed.
      Connect the device to the computer with the USB cable
    • Connect the camera and PC with the USB cable (supplied). "USB Mode" appears on the LCD monitor of the camera.
      NOTE: If the USB cable was connected before the dialog box prompting USB connection appeared, disconnect the USB cable and start again from "Step 1. Start the Updater".
    • Click [OK]. If the message is displayed, close with the [OK] button.
      Press the OK Button
      NOTE: Never turn off the camera nor disconnect the USB cable while updating.

  7. The System Software Updater starts.
    System Software Updater
    NOTE: If System Software Updater does not start up, double-click [System Software Updater] in the [Update_ILCE9M2V200] - [Resources] folder to start up.
  8. Turn on the camera.
  9. Following the instructions in the System Software Updater window, on the camera, select "Menu" → "Setup subpage [3]" → "USB Connection" and make sure "Mass Storage" is selected.
    Setup[3] - Mass Storage
  10. Connect the camera to the computer with the supplied USB cable. "USB Mode" appears on the LCD screen of the camera.
    NOTE: If the computer cannot find the device, the message "Could not find the camera for this update" is displayed on the computer screen. Please try the following:
    • Disconnect the USB cable and connect it again.
    • If the computer has multiple USB terminals, try with the other terminals.

    Sometimes when the camera is connected to the computer with the USB cable, a message prompting you to restart the computer may be displayed. In this case, remove the battery pack from the camera, reboot the computer, and follow the instructions from "2. Start the System Software Updater".
  11. Click [Next]. The current version number and updated version number appear on the lower left side of the screen.
  12. After confirming that the current software version is "Ver.1.01 or earlier", click Next. If the current system software version is 2.00 or later, the update is not required. In this case, disconnect the camera from the computer and click Finish. Turn off the camera, remove the battery pack, reinsert the battery and turn the camera back on.

    Update is required:
    Current Version and Updated Version Numbers
    Update is not required:
    Update is not required
  13. The camera is automatically reset.
    The screen below is displayed.
    The camera is automatically reset
    NOTE: The Loading icon may not be displayed depending on the OS version that you are using.
  14. Start the update.
    After automatically resetting, the following screen is shown and the update starts. The progress bar appears during the update process (approximately 15 minutes).
    NOTE: Never turn off the camera or disconnect the USB cable while updating.
    Update Progress Bar
  15. Complete the update.
    When the update is complete, the camera will automatically restart. Make sure that the camera is turned on and wait until the LCD screen appears again. Click Finish when the LCD screen appears and disconnect the USB cable.
    Click Finish
    NOTE: After restarting, a data recovery warning is sometimes displayed. This is normal. Please wait until this warning disappears.
    Recovering data. Please wait...

Step 2: Confirm the system software version of your device is Ver. 2.00.

  1. On the camera, select Menu → Setup subpage [6] → Version
  2. The system software version is displayed as illustrated below.
    Updated System Software Version

Questions & Answers

The update does not complete

When the monitor remains black for more than 15 minutes, follow these steps to troubleshoot the issue:

  1. Disconnect the USB cable from the computer.
  2. Remove the battery and AC adapter from the camera, leave it for a few minutes, then insert the battery again or connect the AC adapter.
  3. Restart the computer.
  4. Turn on the camera and perform the installation process again.