Sony Support

System Software Update

    Required Downloads
    Applicable Models
    About this download
    System Requirements
    File Info
    Preparation
    Download & Install
    WAIT - Read the Required Files section before downloading this file.

    Required Downloads

    Unless stated otherwise, the file listed below must be installed BEFORE the System Software Update in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

    In order to install the System Software Update the latest version of the nav-u Tool software must be installed on the computer.

    IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

    This information is for the following models:

    • NV-U94T

    About this download

    Benefits and improvements

    This utility updates the NVU-94T nav-u™ portable navigation system software to version 4.01 and provides the following benefits:

    • Improves system stability during Bluetooth™ A2DP streaming
    • Improves the route quality in certain situations
    • Shortens the time to acquire a GPS satellite signal in certain conditions, such as between tall buildings
    • Improves touch panel responsiveness

    System Requirements

    Operating Systems

    • Windows Vista®
    • Windows® 2000
    • Windows® XP
    • Windows® XP MCE

    File Info

    File Name

    • SONYNAVU_U94T_4.1.WC.BIN

    File Version

    • 4.01

    File Size

    • 23.67 MB

    Release Date

    • 12-16-2008

    Before You Start

    Important Notes

    • In order to install this update the nav-u™ Tool must be installed on the computer.
    • To install this update the computer must have an available USB port.
    • Please allow about 10 minutes to perform the system software update.
    • The nav-u device must be fully charged in order to perform a successful system software update.
    • WARNING!!: During the installation of the system software update make sure that you:
      • Do not disconnect the USB cable from the computer or the nav-u device.
      • Do not power off the nav-u device, enter into standby mode, or reset the unit.
      • Do not power off the computer, enter the computer into standby mode, or restart the computer.
      If the system software update process is interrupted the nav-u device may require service at a Sony Service Center.
    • During the installation of this file, be sure that you are logged in as the Administrator or as a user with Administrative rights.
    • To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
    • It is highly recommended to print out these instructions as a reference during the installation process.

    Check the System Software Version

    1. Make sure the nav-u portable navigation device is not connected to the computer.
    2. Power on the nav-u device.
    3. On the nav-u portable navigation system, tap the "MENU" pad to show the Main Menu on the screen.
    4. Tap the "Settings" menu icon, Settings Icon.
    5. At the "Settings" menu, tap "General", scroll to page 5/6, and then tap "Firmware Version".
      Note: It may be necessary to scroll through several screens to locate the "Firmware Version" option.
    6. Take note of the Firmware Version.
    7. At the "Firmware Version" screen, check the firmware version listed. If the firmware version is 4.01 or higher, do not install this system software update.

    Download & Install

    Download and Installation Instructions

    1. To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
    2. Download the SONYNAVU_U94T_4.1.WC.BIN file to a temporary or download directory (please note this directory for reference).
    3. Connect your nav-u personal navigation device to the computer using the supplied USB cable.
    4. Power on your nav-u personal navigation device and wait until the "Connect to PC" message is displayed on the nav-u screen.
    5. WARNING!!: During the installation of the system software update make sure that you:
      • Do not disconnect the USB cable from the computer or the nav-u device.
      • Do not power off the nav-u device, enter into standby mode, or reset the unit.
      • Do not power off the computer, enter the computer into standby mode, or restart the computer.
      If the system software update process is interrupted the nav-u device may require service at a Sony Service Center.
    6. Start the nav-u Tool software on the computer.
    7. At the "nav-u tool" window, click "Upgrade System".
    8. On the right side of the Upgrade Screen, verify that the target version is 1.00.
      Note: If the target version is 4.01 or higher, do not attempt to install this system software update.
    9. On the left side of the Upgrade Screen, click the "Browse" button, and go to the directory where the SONYNAVU_U94T_4.1.WC.BIN file was downloaded and then click "OK".
    10. In the "Name" box, click to select "4.01 wc NV-U94T" update, and then click the button.
    11. After the update file is transferred to the nav-u device a "Transferring Upgrade file completed." message is displayed on the computer.
      WARNING!! Do not disconnect the nav-u device from the computer. The system software update is still continuing. Progress messages are displayed on the nav-u screen.
    12. After the system software update is complete, the nav-u device will automatically shut down and restart.

    Check the System Software Version (optional)

    1. Disconnect the nav-u portable navigation device from the computer.
    2. Tap "Menu" and then tap the Settings tab (the red toolbox).
    3. At the "Settings" screen, tap General.
    4. At the "General Settings" screen, tap "Firmware Version".
      Note: It may be necessary to scroll through several screens to locate the "Firmware Version" option.
    5. At the "Firmware Version" screen, check the system software version listed. If the firmware version is 4.01 the firmware has been successfully updated.
      Note: If the firmware version is not 4.01, please download and install the update again.