IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

  • FDR-AXP35

About this download

Benefits and improvements

This utility updates the system firmware and provides the following benefits:

  • Allows the camera to record XAVCS format video with an SDHC card in addition to SDXC card.
    • When an SDHC memory card is used to record movies in XAVC S format over extended periods of time, the recorded movies will be divided into files of 4 GB, and the divided files can then be integrated into a single file using the Action Cam Movie Creator or PlayMemories Home software
    • Shooting movies in XAVC S format requires SD Speed Class 10, UHS Speed Class U1, or faster
    • When recording at 100 Mbps or more, UHS Speed Class U3 is required

System Requirements

Operating Systems

  • Windows Vista®
  • Windows Vista® 64-bit
  • Windows® 10
  • Windows® 10 64-bit
  • Windows® 7
  • Windows® 7 64-bit
  • Windows® 8
  • Windows® 8 64-bit
  • Windows® 8.1
  • Windows® 8.1 64-bit

File Info

File Name

  • Update_FDRAXP35V110.exe

File Version

  • 1.10

File Size

  • 243 MB

Release Date

  • 04-25-2016

Before You Start

Determine if Your Camera Needs the Update

This update is only for FDR-AX30 and FDR-AXP35 cameras that currently have firmware version 1.00. If your camera firmware version is already Version 1.10 or higher, this update is not necessary.

Check the version of your camera firmware:

  1. Power on the camera.
  2. On the camera, select Menu, General Settings, and then Version.
  3. If the version number is Ver. 1.10 or higher, the camera does not need this update.
    Main Settings Version Number

Important Notes

  • This utility is only for use with the Sony® FDR-AX30 and FDR-AXP35 cameras. Do not install this utility with any other model.
  • WARNING!!: This firmware update and any changes incurred by it are permanent. It is not possible to return to a previous firmware version after updating this firmware. By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
  • This update process requires the following items for proper updating:
    • A computer with:
      • Available Hard Disk Space: 500 MB or more
      • Installed Memory (RAM): 512 MB or more
      • A USB port.
      • One of the following Microsoft® Windows® operating systems installed:
        • Windows 10
        • Windows 8/8.1
        • Windows 7 (with Service Pack 1)
        • Windows Vista® (with Service Pack 2)
          Note: Starter Edition of Windows Vista is not supported.
    • Camera power supply:
      • This update can only be performed when the remaining battery level has three bars Battery Indicater or more. When performing the firmware update, it's recommended to use a fully charged NP-FV70 rechargeable battery pack or AC adapter.
        WARNING!!: The camera may not operate properly if the power is interrupted during the update.
    • USB cable:
      • Use only the USB cable supplied with the camera.
        IMPORTANT: Update functionality is not guaranteed with any other USB cable.
  • To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
  • It is highly recommended that you print out these instructions for use as a reference during the installation process.

Prepare the Camera for the Firmware Update

  1. Remove the memory card from the camera
  2. Ensure the camera battery is fully charged.

Download & Install

Table of Contents

Download and Update the Firmware

  1. Download the Update_FDRAXP35V110.exe file to a temporary or download directory (please note this directory for reference).
    Note: For Windows 8/8.1 and 10, the default settings for Internet Explorer® will save the file in the Downloads folder. For Windows 10, use File Explorer to locate the Downloads folder, for Windows 8/8.1, click the Desktop tile from the Start screen and then locate the Downloads folder using Windows Explorer.
  2. Go to the directory where the file was downloaded and double-click the Update_FDRAXP35V110.exe file to begin the System Software Updater.
  3. At the System Software Updater screen, please follow the instructions.
  4. Power on the camera.
  5. Make sure the USB Connect Setting is set to Mass Storage.

    On the camera, select Menu, Setup, Connection, USB Connect Setting, and then ensure Mass Storage is selected.
    USB Connect Screen
  6. Ensure the memory card is removed from the camera.
  7. Connect the camera to your computer using the supplied USB cable. On the LCD screen of the camera, USB Mode appears. After confirming the connection from the LCD screen of the camera, at the System Software Updater screen, click Next.
    System Software Updater Screen
  8. At the System Software Updater screen, check the version number at the lower left.
    Current Version Screen
    Note: If the current version is 1.10 or higher, your camera does not need this update. Stop the USB connection by clicking the remove hardware icon Remove Hardware Icon or Remove Hardware Icon in the task tray in the lower right corner of the computer screen and then click the Finish button on the System Software Updater screen. Then power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again.
    If the current version is 1.00, click Next to continue with the update.
  9. The camera automatically resets and the following screen appears.
    Please wait... Screen
  10. After automatically resetting, the System Software Updater screen appears with the progress bar while updating (approximately 15 minutes).
    Updating Screen
    WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete.
  11. When the update is completed, the camera will automatically restart. Make sure the camera is powered on and wait until the LCD screen appears again. When the LCD screen appears, click Finish and disconnect the USB cable.
    Update Complete Screen

Check the Firmware Version After Updating (optional)

Please follow the steps below to confirm that the firmware was successfully updated:

  1. On the camera, select Menu, General Settings, and then Version.
  2. If the version number is Ver. 1.10, the camera firmware was successfully updated.
    Main Settings Version Number