WAIT - Read the Required Files section before downloading this file.

Required Downloads

Unless stated otherwise, the file listed below must be installed BEFORE the SEL-35F28Z System Software Update (Mac) in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

This utility is required only with Mac OS X® 10.13.

Applicable Models

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

  • SEL35F28Z

About this download

Benefits and improvements

  • This utility updates the lens system software to version 03 and provides the following benefits:

    Improvements over version 02:

    • Improves the reliability of the focus position when using the camera for long periods of time continuously in MF mode

    Benefits provided by previous updates and included in version 03:

    • Provides the Quick starting function

    Note: The lens must be attached to a camera to perform this update. The NEX-5, NEX-3, NEX-C3, NEX-VG10, and PXW-FS7 model cameras cannot be used.

System Requirements

Operating Systems

  • Mac OS X®

File Info

File Name

  • Update_SEL35F28ZV3D.dmg

File Version

  • 03

File Size

  • 1893206 bytes

Release Date

  • 13-07-2016

Before You Start


Determine if Your Lens Needs the Update 

Check the version of your camera lens System Software:

  1. Attach the lens to the camera.
    Note: Please make sure the camera is off before you attach the lens.
  2. Power on the camera.
  3. Press the Menu button.
  4. At the Menu screen, select Setup.
  5. At the Setup screen, select Version.
  6. The System Software version is displayed on the LCD screen.
    System Software Version Screen
    If the current version is Ver.03 or higher, the camera lens does not need this update.

Important Notes Go to Table of Contents

  • This Lens System Software update can be performed only when the lens is attached to a camera. Make sure to power off the camera and attach your lens before performing this update.
    The NEX-5, NEX-3, NEX-C3, NEX-VG10, and PXW-FS7 model cameras cannot be used.
  • WARNING!!: This Lens System Software update and any changes incurred by it are permanent. It is not possible to return to a previous version after performing this update. By continuing this update process, downloading and installing this software, you acknowledge that you are aware and understand that this update cannot be reversed.
  • This update process requires the following items for proper updating:
    • A computer with:
      • Available Hard Disk Space: 200 MB or more
      • Installed Memory (RAM): 512 MB or more
      • A USB port
      • Apple® Mac OS X® version 10.9 - 10.13
        IMPORTANT: For computers running Mac OS X version 10.13, the DriverLoader_1013 software must be installed before installing the camera software update for each camera that's being updated.
    • A compatible E-mount camera:
      The NEX-5, NEX-3, NEX-C3, NEX-VG10, and PXW-FS7 model cameras cannot be used.
      • When performing the Lens System Software update, please use a fully charged NP-FW50 rechargeable battery pack, or the AC-PW20 AC adapter/charger (sold separately).
        Note: When performing the Lens System Software update using a Broadcast & Production camera, please use the dedicated AC adaptor.
      • Detach the vertical grip before updating lens system software.
    • USB cable:
      • Use only the USB cable supplied with the camera.
        Update functionality is not guaranteed with any other USB cable.
  • To ensure that no other program interferes with the installation, save all work and close all other programs. The Taskbar should be clear of applications before proceeding.
  • It is highly recommended that you print out these instructions for use as a reference during the installation process.

Download & Install


Table of Contents 

--ZZZ--

Download and Update the System Software Go to Table of Contents

  1. Download the Update_SEL35F28ZV2D.dmg file to a temporary or download directory (please note this directory for reference).
  2. Go to the directory where the file was downloaded and double-click the Update_SEL35F28ZV2D.dmg file.
  3. On the desktop, double-click the updater icon.
  4. At the Password prompt screen, enter the user name and password for the administrative account, and then click OK.
    System Software Updater Password.
  5. The Lens System Software Updater starts.
    Connect the Camera Screen
  6. Remove the memory card from the camera.
  7. Ensure the lens is attached the camera.
    Note: Please make sure the camera is off before you attach the lens.
  8. Power on the camera.
    Note: If the camera has already been powered on, power it off and then back on again.
  9. On the camera, press the Menu button, select Setup, and then USB Connection and ensure Mass Storage is selected (this step is not necessary if you are using a QX series camera).
    Mass Storage USB Setting
  10. Connect the camera to your computer using the supplied USB cable.
    Note: If an error message appears on the computer screen, try the following:
    • Disconnect the USB cable and then reconnect it.
    • If another USB port is available on the computer, try connecting the USB cable to another port.
  11. After confirming the steps above, at the Lens System Software Updater screen, click Next.
    Connect the Camera Screen
  12. The camera screen displays the message Follow computer instructions.
    Follow Computer Instructions Screen
    Notes:
    • If the message The update is not available for your model. appears on the screen, verify that the update file is correct for the lens you have attached. If the file is correct, close the Lens System Software Updater program, disconnect the USB cable, power off the camera, and then restart the Lens System Software Updater program and continue the procedure.
    • If the message Could not find the camera with the lens for this update mounted. appears on the screen, ensure you are using a compatible camera (NEX-5, NEX-3, NEX-C3, NEX-VG10, and PXW-FS7 cameras are not compatible) and if the camera is properly connected to the computer. Try disconnecting and reconnecting the USB cable or connect to another USB port on the computer.
  13. WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete.

  14. At the Lens System Software Updater screen, check the version number at the lower left.
    Current Version Screen
    Note: If the current version is Ver.03, your camera lens does not need this update. Stop the USB connection, click the Finish button on the Lens System Software Updater screen, power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again.
    If the current version is Ver.01 or Ver.02, click Next to continue with the update.
  15. The following screen is displayed and the progress bar appears while transferring data to the camera (data transfer takes approximately 5 seconds).
    Transferring Data Screen
    WARNING!!: Do not power off the camera or disconnect the USB cable until the update process is complete.
  16. When the data transfer is complete, the following screen is displayed, click Finish.
    the data transfer Screen
  17. The update process starts and the progress bar is displayed on the camera screen. This process takes approximately 30 seconds to complete.
    Updating the Lens Screen
  18. The update process is finished when the Lens update complete. message is displayed on the camera screen.
    Note: If you are using the QX series, the update process is finished when the message disappears from the camera screen.
    Lens Update Complete Screen
  19. Disconnect the USB cable, power off the camera, and then remove the battery pack or AC adapter.
  20. Reconnect the battery pack or AC adapter and power on the camera.

Check the System Software Version After Updating (optional) Go to Table of Contents

  1. Power on the camera.
  2. Press the Menu button.
  3. At the Menu screen, select Setup.
  4. At the Setup screen, select Version.
  5. The System Software version is displayed on the LCD screen.
    System Software Version Screen
    If the current version is Ver.03, the update was successful.
    Note: If the System Software version number is not Ver.03, please download and install the update again.