IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

  • FDR-AX700

About this download

Benefits and improvements

This utility updates the system software to version 1.01 and provides the following benefits:

  • Optimizes of the peak display level for S-Log shooting
  • Improves the shooting stability of the steady shot in high frame rate shooting
  • Improves the overall stability of camera

System Requirements

Operating Systems

  • Windows® 10
  • Windows® 10 64-bit
  • Windows® 7
  • Windows® 7 64-bit
  • Windows® 8.1
  • Windows® 8.1 64-bit

File Info

File Name

  • Update_FDRAX700V101.exe

File Version

  • 1.01

File Size

  • 178 MB

Release Date

  • 07-23-2018

Before You Start

Determine if Your Camera Needs the Update

This update is only for FDR-AX700 cameras that currently have firmware version 1.00. If your camera firmware version is already 1.01 or higher, this update is not necessary.

Check the version of your camera firmware:

  1. Turn on the camera.
  2. On the camera, select Menu, OTHERS, and then VERSION DISPLAY.
  3. If the version number is 1.01 or higher, the camera does not need this update.
    Current Version
  4. If the version number is 1.00, you should install this update.

Before You Start

  • Follow the update instructions carefully.
  • Your camera needs to be connected to a computer to install the update, but do not make the connection until innstructed to do so.
  • Remove the memory card from the camera
  • This update can only be performed when the remaining battery level has three bars Battery Indicater or more. When performing the firmware update, it's recommended to use a fully charged NP-FV70A rechargeable battery pack or the AC adaptor.
  • This update process requires the following items for proper updating:
    • A computer with:
      • Available Hard Disk Space: 500 MB or more
      • Installed Memory (RAM): 512 MB or more
      • A USB port.
  • Use only the USB cable supplied with the camera. Update functionality is not guaranteed with any other USB cable.
    • Do not operate, turn off, or remove the camera battery or AC adaptor, or allow the computer to enter Sleep (Standby) mode until after the update is complete.
    • This firmware update and any changes incurred by it are permanent. It is not possible to return to a previous firmware version after updating this firmware. By continuing this update process and downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
    • Failure to follow the instructions, or an interruption in the update process, may cause the player to become unresponsive or to require repair.

Download & Install

Download and Update the Firmware

  1. Download the Update_FDRAX700V101.exe file to a temporary or download directory (please note this directory for reference).
    Note: Do not connect the camera yet.
  2. Go to the directory where the file was downloaded and double-click the Update_FDRAX700V101.exe file.
  3. The System Software Updater starts.
  4. Connect the camera to your computer using the supplied USB cable.
    Note: If the message Could not find the camera for this update appears on the computer display, disconnect the USB cable and connect it again. Or, if the computer has multiple USB ports, try connecting to a different USB port.
  5. At the System Software Updater screen, click Next.
    System Software Updater
  6. At the next System Software Updater screen, check the version number.
    Current Version
    Note: If the current version is 1.01 or higher, your camera does not need this update. Stop the USB connection by clicking the Safely Remove Hardware icon Remove Hardware Icon in the task tray on the lower right corner of the computer screen, disconnect the USB cable, and click Finish. Then turn off the camera, briefly remove the battery pack or the AC adaptor, and then turn the camera back on again.
  7. If the current version is not 1.01, click Next to continue with the update.
  8. The camera will automatically reset and the following screen appears.
    Please wait...
  9. A progress bar will be displayed while updating the system software (approximately 20 minutes).
  10. When the update is complete, the camera will automatically restart. Make sure the camera is turned on and when the LCD screen appears again, click Finish.
    Finish the Update
  11. The update has finished and you can disconnect the USB cable.

Check the Firmware Version After Updating

Follow the steps below to confirm that the firmware was successfully updated:

  1. On the camera, select Menu, OTHERS, and then VERSION DISPLAY.
  2. If the version number is 1.01, the camera firmware was successfully updated.
    Current Version
  3. If the version number isn't 1.01, download and install the update again.